Home > S6620 Backplane

	FEATURES 14-slot form factor supports PCI-Express, PCI-X and PCI option cards One SHB Express (PICMG 1.3) System Host Board Slot (Graphics Class) One x16 and one x8 PCI Express Slot Two PCI-X 64-bit/100MHz Slots and Four PCI-X 64-bit/66MHz Slots Four PCI 32-bit/33MHz slots PCI-X slots support universal 64-bit/32-bit PCI cards Four USB 2.0 backplane I/O connections** Two 10/100/1000Base-T backplane Ethernet ports**
**Optional USB, Ethernet, connectivity provided by PICMG 1.3 SHB. Not all SHBs support this capability. Nominal PCB thickness: 0.080" Connector spacing: 0.800" Mounting holes: 0.156" diameter All dimensions are inches.
GRAPHICS-CLASS PCI EXPRESS BACKPLANE Chassis Plans' BPG6600 is a graphics-class backplane that supports a x16 PCIe link from a graphics-class PICMG 1.3 system host board (SHB) to the backplane's PCI Express slot PCIe2. The PCI Express slot labeled PCIe1 is supported by a x1 link from a Chassis Plans IOB31 expansion board. A graphics-class SHB provides an additional x4 link that drives a PCI Express-to-Dual PCI-X bridge chip. Connector D on a graphics-class SHB provides an additional 32-bit/33MHz PCI interface to the BPG6600. SHB SLOT Accepts an SHB Express (PICMG® 1.3) compliant (graphics-class) processor such as Chassis Plans' current T4L or TML system host boards. PCI EXPRESS SERIAL SLOTS PCIe2 is a x16 mechanical slot connected to the SHB with a x16 PCI Express link. PCIe1 is a x8 mechanical and a x4 electrical slot driven by a x1 PCI Express link from the PCIeS expansion slot. In order to use the PCIe1 slot, a Chassis Plans IOB31 I/O expansion board must be used on the graphics-class system host board. The IOB31 enables communication between the SHB/IOB31 and the PCI Express option card in slot PCIe1. PCI-X PARALLEL BUS SLOTS The six PCI-X slots on the BPG6600 are connected to the SHB via a x4 PCI Express link that drives the PCI Express-to-PCI-X bridge chip. The bridge chip provides one 64-bit/100MHz PCI-X channel that support slots B1 and B2 plus an additional 64-bit/66MHz PCI-X channel that supports slots A1 through A4. PCI-X and universal (i.e. 5V/3.3V combo or 3.3V only) PCI option cards may be used and the bridge chip will throttle-down the bus interface speeds to match any universal PCI or PCI-X card with an interface bus speed less than 100MHz or 66MHz. Slots C1 through C4 support 5V only or universal 32-bit/33MHz PCI cards and are driven by connector D of the SHB. OPTIONAL USB 2.0 INTERFACES The SHB Express specification defines optional I/O routings from the SHB to the backplane. Chassis Plans' BPG6600 takes advantage of this new specification feature by providing two USB 2.0 headers capable of providing up to four USB 2.0 backplane ports. Graphics-class system host board support for the USB port connections to a backplane is optional. Refer to the SHB OPTIONAL BACKPLANE I/O SUPPORT TABLE below for an explanation of the backplane I/O capabilities supported by Chassis Plans' PICMG 1.3 graphics-class SHBs or contact Chassis Plans for additional information and SHB product updates. OPTIONAL ETHERNET INTERFACES Chassis Plans' BPG6600 backplane supports the optional Ethernet routing feature of the SHB Express (PICMG 1.3) specification. Two 10/100/1000Base-T Ethernet RJ-45 connectors are available for use on the backplane. Data communication performance of the backplane's Ethernet interfaces depends on the Ethernet controller hardware and configuration on the system host board. Consult your SHB Ethernet interface implementation method for details. The SHB OPTIONAL BACKPLANE I/O SUPPORT TABLE explains the backplane I/O capabilities supported by Chassis Plans' PICMG 1.3 System Host Boards. POWER CONNECTORS The BPG6600 backplane is available with power connectors suitable for use with either an ATX or EPS power supply. EXTENDED-CURRENT TERMINAL BLOCKS Two extended-current terminal blocks provide additional power capacity for power-intensive applications -- up to 80 Amps of +12V, 80 Amps of +3.3V and 40 Amps of +5V.	POWER INDICATORS Surface-mount LEDs provide a convenient visual check for +5V, -5V, +5V AUX,+12V, -12V and +3.3V power connection and status. CAUTION: Never install or remove the SHB or any option card from the BPG6600 backplane if the +5V AUX LED is GREEN. If the system appears to be off and the+5V AUX LED is GREEN then you need to remove or turn-off the incoming power to the system power supply. AUXILIARY POWER CONNECTOR The +12V power connector on the BPG6600 routes auxiliary power to the SHB's edge connectors. This new capability of PICMG 1.3 compliant SHBs and backplanes eliminates the need for auxiliary power connections on the system host board. PRINTED CIRCUIT LAYERS The backplane is a six-layer, .080" thick board with three separate signal layers: +5V/+12V, +3.3V and ground. Multi-layer backplane construction provides excellent noise immunity. CONNECTING POWER The combination of new power supply technologies, soft-power control signals available via the Advanced Configuration and Power Interface (ACPI) now supported by PICMG 1.3 SHBs and auxiliary power connectors on PICMG 1.3 backplanes that deliver all of the SHBs power to the edge connectors are requiring a different approach to connecting system power. Auxiliary power connectors on the backplane are provided to help improve system Mean Time To Repair (MTTR). All power can be delivered to the SHB via the board's edge connectors. Chassis Plans' PICMG 1.3 SHBs and backplane SHB edge connector slots have ample power pins available to meet the power demands of high-performance, performance-based processor SHBs like the Chassis Plans T4L. The ATX/EPS and +12V power connectors on the BPG6600 backplane also have an ample number of power pins available to meet these demands. The system designer needs to be aware of the potential power demands of the entire system including the particular SHB to ensure that both the power supply and the power connectors in the cable harness can safely deliver the necessary power to drive the entire system. Specific implementations of ACPI signals, ATX/EPS power supply type and the operating system software will determine the specific connection method for the power supply. For example the use of the Power Good (PWRGD), Power Supply On (PSON#), Five Volt Standby (5VSB) and the Power Button (PWRBT#) ACPI or soft power control signals require the following connection method: ACPI signal usage is optional and may be turned off using the SHBs BIOS and/or signal jumpers. Specific power connections and BIOS parameters will differ according to unique system design requirements. For more information refer to the Appendix B (Power Connection) and Advanced Setup BIOS sections of any Chassis Plans Technical Reference Manual for graphics-class system host boards such as the Chassis Plans T4L or TML.
SHB OPTIONAL BACKPLANE I/O SUPPORT TABLE
Chassis Plans ETHERNET USB SATA SHB LAN0 LAN1 USB0 USB1 USB2 USB3 SATA0 SATA1 T4L - X1 X2 X2 X3 X3 - - TML - X1 X2 X2 X3 X3 - - 1 The LAN1 port on the backplane will function as a 10/100Base-T Ethernet interface and the operating system may logical recognize the interface as LAN2 2 Requires a T4L/TML factory build option. The operating system may logical recognize these interfaces as USB ports 4 and 5. 3 These two USB interface backplane routings are standard on the T4L and TML SHBs. The operating system may logical recognize these interfaces as USB ports 6 and 7.
MODEL NAME: BPG6600
MODEL# MODEL NAME DESCRIPTION S6600-004 BPG6600-EPS Vertical EPS/ATX and +12V AUX connectors with two high-current terminal blocks S6600-007 BPG6600-CRA Right-angle EPS/ATX and +12V AUX connectors with two high-current terminal blocks
PCI Express Backplanes Reference Manual (3.2MB) - Click Here